Fiberlock Lag-Kote Interior/Exterior Lagging Encapsulant (5 GL)

Fiberlock Tehcnologies Lag-Kote is a white, 100% acrylic, high solids encapsulant/sealant specifically formulated for application over a variety of Asbestos Containing Materials (ACM). Tested at Battelle Laboratories of Columbus, Ohio, under EPA Contract #08-03-2552-T2005, Lag-Kote was found to be acceptable as an asbestos encapsulant.
Designed to encase spray-on fireproofing, asbestos-containing plasters and paints, transite, and asbestos-containing thermal insulation, Lag-Kote's viscous formulation minimizes dripping, cleanup and product waste.
Lag-Kote provides a smooth, washable, aesthetically superior finish that will provide years of lasting protection. Lag-Kote has excellent resistance to alkalis and can be applied directly over galvanized metal, wood, masonry or other sound surfaces.
UV inhibitors make Lag-Kote suitable for encasement of exterior transite siding and asbestos fortified paint systems. Lag-Kote is water based.

SURFACE REPAIRS & CLEANING

Lagging that is torn, ruptured or delaminated should be repaired with:
Patching Cement: Mix cement with water and cap all exposed ends and voids.
Lag Kloth Water-Activated Repair Cloth: Lag Kloth should be dipped in water and applied to the asbestos containing material. Upon completion of repairs, prepare the surface for the application of Lag Kote. Thoroughly remove all dust and dirt that has accumulated on lagging or covering, use a vacuum with a HEPA filter specifically designed to capture hazardous dust and waste or wipe surfaces with a damp cloth. Do not air clean surfaces; this could increase asbestos exposure.

APPLICATION TOOLS

Apply Lag Kote with brush, roller or airless spray equipment.
Brush: Synthetic, nylon or polyester bristle | Roller: Synthetic Fiber 3/8 nap or longer | Spray Settings: Pressure: 2200-2700 P.S.I. Tips: .015 to .019 tips

MIXING

Lag Kote may be diluted by adding up to 10% water. Prior to application, stir Lag Kote thoroughly to achieve a uniform consistency. Lag Kote can be tinted to pastel colors.

PRODUCT APPLICATION

Select a brush, roller or painter's mitt for convenient application to the ACM. Apply 1-2 coats of Lag Kote to the desired film thickness. Minimum film thickness may vary with desired results and type of application.

COVERAGE

Smooth Surfaces: 125-175 sq. ft. per gallon (5 dry mils) | Porous Surfaces: 75-100 sq. ft. per gallon (5 dry mils)

DRYING TIME

@ 70°F: 50% R.H. | To Touch: 1-2 hours | Recoat: 8-16 hours

CLEANUP

Tools and drippings should be cleaned with warm soapy water before coating dries. Follow equipment manufacturerâ„¢s directions to clean spray equipment. Dispose of all waste according to current local, state and federal regulations.

PRECAUTIONS

Store in a dry place at temperatures between 40°F (4.5°C) and 90°F (32°C). Approved respirators must be used to prevent inhalation of asbestos fibers that may be present in the air. Protective clothing should be worn. Careful consideration must be given to all EPA, OSHA, federal, state and local regulations in effect prior to the application of this product.

• Product Type: Lag Kote II Interior/Exterior Lagging Encapsulant
• Color: White
• Size: 5 gal
• Form: Liquid
• Composition: 1 to 5% Propylene Glycol, <1% Chlorothalonil, 0.5 to 5% Monoisobutanolamine, 5 to 15% Titanium Dioxide, 10 to 15% Kaolin, 0.5 to 5% 2,2,4-Trimethyl-1,3-Pentanediol Monoisobutyrate, 1 to 5% Zinc Oxide
• pH Value: 8.5
• Container Type: Pail
• Shelf Life: 3 years
• Viscosity: 120 to 130 Kreb Units
• Weight: 55.000